- Can exposed speaker wire cause a fire?
- Can you hang something above an outlet?
- Can a nicked wire cause a fire?
- What should you do if you drill through a wire?
- Can I drill above a plug socket?
- How do most electrical fires start?
- What happens if you hit a wire with a nail?
- How would I know if I hit a wire with a nail?
- Can you hang a picture above a plug socket?
- How far behind drywall are wires?
- How do you know if it’s safe to drill into a wall?
- How do you fix a burnt electrical wire?
- Is it safe to put electrical tape over exposed wires?
- Can you drill above a fuse box?
- Can I put a nail above a light switch?
- Do electrical cables run up or down?
- Do stud finders detect wires?
- Where do electrical wires run in walls?
Can exposed speaker wire cause a fire?
As Bill said in post #2 , yes, it is possible, but it is unlikely.
Amps have protection circuits in them and should shut down in the event of a short circuit.
However, if there is a fire unrelated to the wire itself, the wire could give off toxic fumes..
Can you hang something above an outlet?
If you go higher than 10″ above outlets; chances are remote you will hit anything; as the wires usually run down the stud to either side .
Can a nicked wire cause a fire?
Factors such as nicked wires, loose connections, improper wire size, reversed polarity (hot and neutral wires connected to the wrong terminals) and poor or no grounding of metal parts of electrical equipment can cause fires, shock and electrocution.
What should you do if you drill through a wire?
If the conductor is damaged then the only proper solution is to either replace the cable or install an accessible joint box. The only real way for they guy to find out is to remove some of the plaster around the drill hole to see.
Can I drill above a plug socket?
Don’t drill directly above or below light switches and plug sockets. Invest in a stud finder/metal detector (as mentioned above) that will detect wires and pipes. If you do mistakenly drill into a water pipe, think of the little boy with his thumb in the dyke and LEAVE THE DRILL BIT IN THERE.
How do most electrical fires start?
Most electrical fires are caused by faulty electrical outlets and old, outdated appliances. Other fires are started by faults in appliance cords, receptacles and switches. … Removing the grounding plug from a cord so it can be used in a two-prong electrical outlet can also cause a fire.
What happens if you hit a wire with a nail?
When hammering in nails, it is best to drive them into a wall stud. According to Realtor.com, most homes have wires and pipes behind the walls, and there are no guarantees as to their locations. … Hitting a wire or pipe could cause serious injuries to the person holding the drill and could damage the home as well.
How would I know if I hit a wire with a nail?
The only way you could have hit a wire with a nail that short is if the wire was laying over the stud and the drywall was placed over it, pinching it between the two. If that were the case, you should notice a hump in the wall there somewhere.
Can you hang a picture above a plug socket?
Don’t hang pictures above light switches (or sockets, if you want to be on the safe side) or to the left/right of sockets. You should be fine, unless your house has form for weirdness.
How far behind drywall are wires?
Wires. Electrical cables are usually behind drywall, either running horizontally through holes in the studs or stapled vertically up the sides of studs. Outlet cables tend to be about 12 inches high. Light switches are around 48 inches high, so expect to see electric cables around that area.
How do you know if it’s safe to drill into a wall?
One rule of thumb is to be especially careful when drilling into any walls that connect to your bathroom or kitchen—basically, any wall that’s likely to have pipes. If you do hit a pipe, Williams says, you’ll probably know it.
How do you fix a burnt electrical wire?
Steps to fix burned electric wiringGet new wire insulation. To begin with, peel off the outer jacket of the nonmetallic cable. … Reinsulate the old wires. Remove as much of the old insulation as is possible. … Shrink the tubing. To shrink the tubing, wave a lighter flame under the heat shrinkable tubing.Nov 21, 2016
Is it safe to put electrical tape over exposed wires?
Electrical tape, typically black in color, should be used on exposed electrical wires because of its low conductivity and durability to wear and tear over time. For larger gashes and cuts in electrical wires, you may need to fully cut the wire and make an electrical connection using wire nuts.
Can you drill above a fuse box?
Never for any reason unless you’re a trained electrician or installed everything your self, and know for 100% certainty where everything is, should you ever drill around a panel. Its nestled between two studs, so you could always drill into those. But you’re not supposed to cover or obstruct a fuse box.
Can I put a nail above a light switch?
Electrical wires typically run either vertically, up and down the side of a stud or horizontally. The vertical wires are typically pretty easy to avoid: avoid drilling above a receptacle or light switch. … A single 1 1/2-inch (4d) or 2-inch (6d) finishing nail will support most pictures, even when nailing between studs.
Do electrical cables run up or down?
Safety Zones for Electrical Cables in Walls There are a number of electrical wiring safe zones in which the cables should run: … Vertically from any switch or socket – the safety zone runs the width of the socket or switch both up to the ceiling and down to the floor.
Do stud finders detect wires?
All stud finders do the same basic thing: detect where support areas like studs and joists are inside the walls. All stud finders can detect wood, most detect metal, and many also detect live electrical wiring.
Where do electrical wires run in walls?
Electrical wires typically run either vertically, up and down the side of a stud (with staples), in order to reach receptacles, ceiling lights/fans, etc., and horizontally in order to get across the room(s).