Question: Can I Hang A Picture Above A Light Switch?

Can you hang a picture over a light switch?

You can arrange the art or photographs around it so your eye is drawn to the images rather than the switch or outlet.

You can even frame out the light switch to make it blend in even more..

How do you hang 4 pictures on a wall?

To hang a group of 4 pictures for example, consider hanging it as one entire square. Then place pictures so that the center point of the piece or grouping is at approximately eye level. NOTE: A dining room wall decoration arrangement is best slightly lower, to enjoy looking at it most while you are sitting down.

Should you put pictures on every wall?

The key to any successful interior design is balance. That means when it comes to hanging pictures, no, you don’t need to fill every wall space with pictures. Empty wall space can be used as a crucial design element to enhance your décor.

How high do you hang pictures on a 10 foot wall?

A good rule of thumb is to hang art so that its midpoint is between 57 and 60 inches from the floor.

Can you drill near light switch?

“One common rule is to avoid drilling around light switches and sockets, as the electrical wires can go horizontally and vertically around these fixtures,” Williams explains. “You can also get an idea of where wires and pipes run by looking in the attic and basement to see where they go up or down through framing.”

Can I drill above a plug socket?

Don’t drill directly above or below light switches and plug sockets. Invest in a stud finder/metal detector (as mentioned above) that will detect wires and pipes. If you do mistakenly drill into a water pipe, think of the little boy with his thumb in the dyke and LEAVE THE DRILL BIT IN THERE.

Can you drill above a fuse box?

Never for any reason unless you’re a trained electrician or installed everything your self, and know for 100% certainty where everything is, should you ever drill around a panel. Its nestled between two studs, so you could always drill into those. But you’re not supposed to cover or obstruct a fuse box.

Are outlets on a stud?

Yes, in general electrical outlets are installed directly next to a stud. However, apartments may have some different things going on: There may be metal studs. … With a wall plug, it’s mostly the drywall that will hold it up.

Do you center pictures on wall or over furniture?

Artwork should be centered over the furniture such as a sofa, bed or mantel. Artwork placed above a main piece of furniture in the room should be placed no more than six inches above the piece of furniture in order to make them appear cohesive.

Do electric cables need to be in conduit?

9 Answers from MyBuilder Electricians Your electrician definitely should have used some sort of containment such as capping/conduit. That fact that you can see the cable is evidence that the cables are inadequately mechanically protected. All cables should either be contained in steel conduit or protected by 30mA RCD.

How far can you run an electrical line?

As an example, for a 120-volt circuit, you can run up to 50 feet of 14 AWG cable without exceeding 3 percent voltage drop….For 240-volt circuits:14 AWG100 feet12 AWG120 feet10 AWG128 feet8 AWG152 feet6 AWG188 feetDec 21, 2020

Is it safe to hang a picture over an electrical outlet?

You can accomplish what you are asking with far less risk or hitting the electric line by using a wall anchor that is rated for slightly more than the weight of your planned picture. But, with caution, yes – you can hang the picture over the high receptacle and anchor it to the wall.

What is the rule for hanging pictures?

The golden rule of hanging a picture is to have the center of the photo be at 57 inches. This reflects the standard eye-height of the average person, and is used as a standard in most art galleries and museums.

Do electrical cables run up or down?

Safety Zones for Electrical Cables in Walls Top of the wall – where the wall meets the ceiling there is a 150mm zone where cables should be run. … Vertically from any switch or socket – the safety zone runs the width of the socket or switch both up to the ceiling and down to the floor.

What happens if you nail into a wire?

Hitting a wire or pipe could cause serious injuries to the person holding the drill and could damage the home as well. Aside from you getting electrocuted and ending up in the emergency room, a fire could start, or your home could get flooded.

Do stud finders detect wires?

All stud finders do the same basic thing: detect where support areas like studs and joists are inside the walls. All stud finders can detect wood, most detect metal, and many also detect live electrical wiring.

What happens if I drill into a wire?

Damage to electrical wiring from drilling into walls is a surprisingly frequent phenomenon – especially when buildings are being renovated. … In the worst case, if the protective earth conductor has been damaged you otherwise run the risk of a fatal electric shock.

Can you cover an electrical outlet?

As long as there are no wires inside the box, you can cover it with drywall. If the box is still acting as a junction box, however, and wires are joined inside it, the electrical code mandates a removable cover. Covers come in plastic or metal, and you attach them with machine screws.

Can you cover an outlet with a mirror?

2 Answers. You’re fine just so long as the receptacles is accessible and as long as you can take the mirror down to service it as need be I don’t see a problem.

How far behind drywall are wires?

Wires. Electrical cables are usually behind drywall, either running horizontally through holes in the studs or stapled vertically up the sides of studs. Outlet cables tend to be about 12 inches high. Light switches are around 48 inches high, so expect to see electric cables around that area.

Can you run electrical wire under house?

individual wires can not be run outside of conduit (except for direct burial rated wires buried 24in deep). They need to be in pipe or a cable must be used. you also cannot rely on your inspector to make sure the electrician is doing the work to code. that is the electricians responsibility.